Solid State Logic Duality 82S6DUA20C User Manual Page 78
- Page / 127
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
The majority of DAW functions are controlled via dedicated Duality front panel switches, with less reliance than
the HUI protocol on the 8x8 soft key matrix located beneath the TFT screen. All plug-in editing is via the channel
D-pots. The four encoders, together with the six switches below the centre section monitor screen, are not used
with the Mackie Control protocol.
On the channel fader strips, the auto button and associated status LEDs are also not implemented by the
protocol. All other controls, the D-pot and associated push switch, DAW channel Solo and Cut, plus the Select
and Ready functions, are all fully supported. Only mono metering information is returned from the workstation.
On stereo channels, the maximum value of the left or right channel is displayed. The master fader is also
included in the DAW layer when a Mackie Control template is active.
The AUTO, PRE, IN, OUT etc. group of centre section buttons provide different related motion control functions
according to the active template. When required, tallies for these buttons will be displayed on the TFT display in
the area next to the DAW timeline counter.
The jog wheel, together with the SCRUB button, plus the cursor buttons and cursor mode switch, are active in
all templates. The outer jog wheel ring is not supported, neither is the numeric keypad. However the 1-8 keys
replicate F1 - F8 function keys in certain templates.
Mackie Function Control Overview
As far as possible, all the function templates use button groupings and layouts that follow the original Mackie
Control surface groupings, in order to simplify moving from one DAW platform to another:
Channel D-pot functions and display options (1)
The rotary encoder switch flips D-pot parameters onto the channel faders. The encoder itself is not used in any
of the Mackie Control templates. The CHANNEL button has the same functions as in HUI Mode, and assigns
either the console or DAW channel level control to the D-pot, according to the state of the Console Focus button.
Push to Flip
CHANNEL
RDY
SEL
CHANNEL
1
2
3
4
5
6
7
8
DAW Control GuidE
3-28
Duality Operator’s Manual
- Operator’s Manual 1
- Solid State Logic 2
- Table of Contents 8
- TTOOCC--66 8
- Section 1 – Introduction 9
- Exceptional Signal Processing 10
- Creative Versatility 10
- DAW Controller 11
- Controller Features Summary 11
- System Options 11
- About this manual 12
- Contacting Solid State Logic 12
- Overview 13
- An Introduction to Split Mode 14
- Routing and Signal Flow 14
- Channel Strip 15
- Channel Input Section 16
- Dynamics Section 17
- Equaliser 19
- Channel Output (CHOP) 20
- Signal Processor Routing 20
- Channel Sends 21
- Split Mode 22
- Channel Pan 22
- D-pot and DAW Control 23
- Channel Cut and Solo 23
- Channel Fader 23
- Fader Grouping 24
- The Channel TFT Screen 24
- Channel Processing Order 25
- Channel Metering 25
- DAW Status Indicators 25
- Console Operator’s Guide 26
- Duality Operator’s Manual 26
- The Centre Section 27
- Central Routing Panel 28
- Main Output Functions 30
- Main Bus Compressor 31
- Master Fader 32
- Track Bus Master Controls 33
- Monitoring 34
- External Source Selectors 35
- Monitor Insert 36
- Monitor Metering 36
- Monitor Options 37
- Bass Management 37
- Monitor Level Calibration 39
- SOLO / AFL / PFL 40
- Cue/FX Send Master Controls 41
- Stereo Return Channels 42
- Misc Options 43
- Communications 44
- Oscillator 45
- Mix Reassign Matrix 46
- LFE Channel 46
- Stereo Mix Matrix 46
- Group Control Faders 47
- Centre Section Metering 48
- Setup Menu 49
- DAW Control 50
- Section 3 – DAW Control Guide 51
- Console Focus 53
- Channel Banking Controls (6) 53
- DAW Window Buttons (13) 54
- DAW Utility Buttons (9) 54
- Modifier Buttons (10) 55
- The Default Button (7) 55
- Channel Functions 56
- Channel Solo and Cut Panels 57
- Record Ready Mode 58
- Edit Mode 58
- Select Mode 59
- Setting Sends Pre/Post Fader 60
- Muting a Send Output 60
- Motion Control 62
- Other useful transport modes 63
- Footswitch Control 64
- Numeric Keypad (18) 66
- Plug-In Editor 67
- Plug-In Display Modes 68
- Selecting a Plug-In to Edit 69
- Changing Plug-in Parameters 69
- Comparing Your Changes 70
- Bypassing Plug-ins 70
- D-pot Sensitivity 70
- Soft Keys 71
- Edit Tools Menu 72
- Edit Modes Menu 72
- Status/Group Menu 72
- Function Keys 73
- EDIT Menu 73
- SSL Menu 73
- Working with DAW Automation 74
- Automation Status Display 75
- Suspending Automation 75
- Automating Cuts 76
- Automating Pans and Sends 76
- Automating Plug-Ins 76
- Implementation 77
- Push to Flip 78
- The Logic Template 79
- CYCLE DROP REPLACE CLICK SOLO 80
- Nuendo/Cubase Template 82
- LEFT RIGHT CYCLE PUNCH 83
- PREV ADD NEXT 83
- The Sonar Template 85
- Digital Performer Template 88
- DAW Control GuidE 90
- Section 4 – Total Recall 91
- Total Recall and Projects 92
- Saving a TR Setup 93
- Recalling a TR Setup 94
- Deleting a TR Setup 94
- Renaming TR Setups 94
- Total Recall Displays 95
- Resetting soft switches 96
- OOvveerrvviieeww 97
- Project 1 Title 1 — selected 99
- Project 2 Title 2 99
- OOppeerraattiioonn 100
- Mix Enabled 101
- Project 16 :: Title 1 101
- 00 : 02 : 12 : 23 102
- Mix Review 104
- Mix Running 104
- DDiissccaarrdd 105
- TTrriimm 106
- TTrriimm LLoocckk 107
- MMoottoorrss OOffff 108
- SSnnaapp MMooddee 108
- AAuuttooTTaakkeeoovveerr 108
- CUT UNCUT 109
- UT UNCUT 109
- CCooppyy aanndd SSwwaapp 110
- FFaaddeerr LLiinnkkss 111
- Introduction 117
- Setting a Fixed IP Address 118
- Connecting to Duality 119
- Project Tab 120
- Backing up a Project 121
- Restoring a Project 121
- Notes Tab 121
- Channel Tabs 122
- Total Recall 124
- Exts Names 125
- Misc Tab 126
- Operator's 127
© 2020, manymanuals.com. All rights reserved. | 0.816 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals